5-100TPD Continuous and automatic waste plastic pyrolysis to fuel oil equipment with CE/ISO from LD
Introduction of 5-100TPD Continuous and automatic waste plastic pyrolysis to fuel oil equipment with CE/ISO from LDlow-temperature-press (LP), high-temperature-press.
external processing, using teaseed as raw materials.
one can run Shandong Microwave Machinery Co.,Ltd.factory with Shandong Microwave Machinery Co.,Ltd. refining equipment.
one can sell 5-100TPD Continuous and automatic waste plastic pyrolysis to fuel oil equipment with CE/ISO from LD while pressing at the market.
Functions of 5-100TPD Continuous and automatic waste plastic pyrolysis to fuel oil equipment with CE/ISO from LD
(1) 5-100TPD Continuous and automatic waste plastic pyrolysis to fuel oil equipment with CE/ISO from LDRefining section: used to P-acid de-gumming, alkali refining de-acid and water rinsing.
(2) Teaseeds oil machineryDecoloring section: used to remove off pigments, bleaching oils and grease dehydrate.
(3) Teaseeds oil machineryDeodorizing section: to remove off the odor components in oil.
(4) Teaseeds oil machineryDewax: used to remove off the wax in the oil, in order to get the high quality oil.
(5) 5-100TPD Continuous and automatic waste plastic pyrolysis to fuel oil equipment with CE/ISO from LDHeattransfer oil stove: supply each device production needing heat energy, temperature reach above 280°C.
(6) Teaseeds oil machinerySteam generator: produce the needing steam for de-odoring and distillation.
(7) 5-100TPD Continuous and automatic waste plastic pyrolysis to fuel oil equipment with CE/ISO from LDVacuum pump: supply needing vacuum for dehydrate, de-color, de-odor. Vacuum degree can reach above 755mm Hg.
(8) Teaseeds oil machineryPress filter: filter clay, filter out clear oil.
(9) 5-100TPD Continuous and automatic waste plastic pyrolysis to fuel oil equipment with CE/ISO from LDAir compressor: blow dry bleached clay, blow empty the leftover oil in the press filter.
1. Catalytic pyrolysis reactor
The device is designed to completely overcome the current domestic vertical and horizontal uneven heating kettle, easy to break, low yield, short life and other shortcomings. I designed the rotary autoclave to overcome the above drawbacks, using a 360-degree horizontal rotation structure, 1.2 or 1.0 rotations per minute turn, will make the overall heating kettle body, increasing heated area, improve the fragmentation rate of raw materials.
2. Slag system
Current domestic production of reactor, because it is a fixed structure, so the slag is slow, the slag is not clean and other unfavorable factors. The rotating vessel inside the unique design, resorted slag achieve a fully automatic, with the slag fast, slag and clean and other advantages.
3. Environmental Systems
Dust: Wet flue dust I designed and dry dust barrier system S-shaped, with desulfurization dust, dust removal rate of 95% or more, soot emissions can be achieved GB 13271-2001 standards. Completely solve the problem of black smoke are not environmentally friendly. Dust is removed by wet and dry dust chamber dust chamber dust S-shaped barrier, discharge, due to the induced draft fan means, so the chimney can be buried in.
Waste: The waste plastics by catalytic pyrolysis, there will be some solid residue, waste accounts for about 5% to 10% by weight of the plastic. Its main component is a coarse carbon black. Fly ash can be used as raw material for the production of industrial carbon black, and can also power plants with coal as raw material to produce a mixture, as fly ash brick manufacturing (an environmentally friendly building materials) of raw materials. Because of the ash contamination when sanitation, we have adopted a national patent slag technology.
Wastewater: Throughout the production process, only the condenser and the cooler water, while it is cooling effect, can be recycled, since the seal which produced only one ton 50 kg tractable small amount of waste heat can be dedicated flue neutralization treatment.
4. Flashback eLDaust system
The use of waste plastics, waste rubber refining fuel oil in the process, there are some at normal temperature and pressure can not be liquefied flammable gas, such as air pollution can cause direct emissions. Our self-developed medium-pressure gas burners, very effective solution to this problem, the eLDaust gas through two safety devices and tempering seal stopper at the bottom combustion, one can prevent air pollution, on the other hand You can save a lot of fuel
5. Free distillation refining system
After my company's refining system set free distillation process out of the plastic oil, the color is light red or pale yellow, greatly improve the market price of plastic oil. Equipment cost of the system relative to the current system was purified by distillation or vacuum distillation systems on the market is its equipment cost of 1/4 or 1/5.
6. The latest oil catalytic cracking technology
Waste plastics usually pyrolysis oil technology to be recovered, that is, by heating or adding some catalyst to decompose the waste plastic. Eligible and polymerization monomers, vegetable oil, gasoline and fuel oil gas, floor wax. Waste plastics pyrolysis oil is not only pollute the environment, and can effectively recover energy. We can say that waste plastic pyrolysis oil is a petroleum-based raw materials for the reverse process of oily chemical industry manufacture plastic products. Our company based on the composition of the waste plastic is different, with different catalytic cracking catalysts, compared with domestic production of pyrolysis oil technology, increasing oil yield and improve the oil quality.
1, due to the different composition of waste plastics, which cleaves behavior also varies, polyethylene (PE), polypropylene (PP) and polystyrene (PS) at 300-400 ℃ almost all of this decomposition. And polyvinyl chloride (PVC) at 200-300 ℃ and 300-400 ℃ decompose in two stages. Line at a lower temperature to release HCL, and generate more hydrocarbon, and then further decomposed at a higher temperature. Since HCL device has some corrosion, but also affect the quality of life and cracking catalysts and diesel fuel, gasoline. Therefore, the general requirements for cracking feedstock PVC waste plastics containing not more than 30%.
2, catalytic cracking products, different plastics due to the large difference in the molecular structure, and thus the composition and recovery catalytic pyrolysis products is not the same. In general, thermal decomposition products of four categories: hydrocarbon gases (C1-C5), oils (gasoline molecules of carbon atoms C5-C11, diesel carbon molecules atoms C12-C20, heavy carbon molecules atoms C20), paraffins and coke .
customers and honors
Shandong Microwave Machinery Co.,Ltd.is a Teaseeds oil machinery factory specializing in the production of 5-100TPD Continuous and automatic waste plastic pyrolysis to fuel oil equipment with CE/ISO from LD, scientific research,manufacturing,installation, commissioning.Shandong Microwave Machinery Co.,Ltd.can provide Teaseeds oil machinerycustomers with design and services of 1-2000 tons 5-100TPD Continuous and automatic waste plastic pyrolysis to fuel oil equipment with CE/ISO from LD. Shandong Microwave Machinery Co.,Ltd. have finished hundreds of successful projects Teaseeds oil machineryover the years: peanut oil, soybean oil, rapeseed oil, cottonseed oil, sunflower oil, sesame oil, animal oil,grape seed oil, acer truncatum oil, peony seed oil, walnut oil, hemp seed oil, pine oil, tea seed oil, papaya oil, milk thistle seed, and other special type Teaseeds oil machineryoil. Shandong Microwave Machinery Co.,Ltd. have independent import and export department. Shandong Microwave Machinery Co.,Ltd. Teaseeds oil machineryequipment has been successfully exported to more than ten countries: Russia, Australia, India, Afghanistan, Cameroon,and so on.